ACUMEN INSTRUMENTS CORPORATION DataBridge™ SDR2-USB Configuration Guide revision 1.0 • 04/2009
Getting Started SDR2-USB Configuration Guide rev 1.0 8 Figure 1.3. Creating setup.txt. Once the file is created, double-click it to open the file i
SDR2-USB Configuration Guide rev 1.0 Configuring the DataBridge SDR2-USB 9 22 2. Configuring the DataBridge SDR2-USB Now that you’ve
Configuring the DataBridge SDR2-USB SDR2-USB Configuration Guide rev 1.0 10 2.1 Comments Within the setup.txt file, it is useful to record comments
SDR2-USB Configuration Guide rev 1.0 Configuring the DataBridge SDR2-USB 11 NOTE: By default, the SDR2-USB uses a serial data format of eight data b
Configuring the DataBridge SDR2-USB SDR2-USB Configuration Guide rev 1.0 12 Hardware handshaking prevents a data source from sending data when the S
SDR2-USB Configuration Guide rev 1.0 Configuring the DataBridge SDR2-USB 13 Figure 2.3. Specifying filename and folder for recording. 2.5 Configur
Configuring the DataBridge SDR2-USB SDR2-USB Configuration Guide rev 1.0 14 feed is received by adding the line TimestampTrigger=10. The recorder w
SDR2-USB Configuration Guide rev 1.0 Operations 15 33 3. Operations 3.1 Setup file reading The setup.txt file on the USB storage de
Operations SDR2-USB Configuration Guide rev 1.0 16 3.2.2 Stopping recording Incoming data is written to the open file as it is received until you st
SDR2-USB Configuration Guide rev 1.0 Operations 17 NOTE: If your USB storage media was included with SDR2-USB, it is already formatted properly. D
Operations SDR2-USB Configuration Guide rev 1.0 18 3.3 Lithium battery maintenance The SDR2-USB's real-time clock uses a small lithium battery
SDR2-USB Configuration Guide rev 1.0 Setup File Reference 19 44 4. Setup File Reference All SDR2-USB configuration is performed via th
Setup File Reference SDR2-USB Configuration Guide rev 1.0 20 4.1.2 Data Port Setup Commands DataPortBaud (default=9600): Use this setup file comman
SDR2-USB Configuration Guide rev 1.0 Setup File Reference 21 possible when space available on the storage media is exhausted. Together with schedul
Setup File Reference SDR2-USB Configuration Guide rev 1.0 22 TimestampTrigger: The TimestampTrigger setup file line specifies a decimal ASCII charac
SDR2-USB Configuration Guide rev 1.0 J4 Remote Control Port 23 55 5. J4 Remote Control Port 5.1 Overview The SDR2-USB’s J4 remote conne
Setup File Reference SDR2-USB Configuration Guide rev 1.0 24 5.3 Functions Table 5.1 describes the functions of the J4 remote connector. VDD (3.3V
SDR2-USB Configuration Guide rev 1.0 J4 Remote Control Port 25 Contact Function Direction Wire Color 1 VDD (3.3 VDC) - 2 GND (0 VDC) Black 3 i
SDR2-USB Configuration Guide rev 1.0 Service and Support 27 66 6. Service and Support 6.1 Exception Codes The following are common erro
Copyright This document is copyrighted by Acumen Instruments Corporation with all rights reserved. No part of this document may be reproduced in any f
Service and Support SDR2-USB Configuration Guide rev 1.0 28 Exception 4: Bad Boot Record Occurs when the disk is completely unformatted or formatted
SDR2-USB Configuration Guide rev 1.0 Service and Support 29 6.2 Contacting Acumen Instruments Corporation 6.2.1 Technical support Service and techn
Service and Support SDR2-USB Configuration Guide rev 1.0 30 6.4 Warranty 6.4.1 One year warranty Acumen Instruments Corporation warrants this produc
SDR2-USB Configuration Guide rev 1.0 Serial Port Basics 31 AA A.Serial Port Basics A.1 Serial specifications Serial data is any dat
Serial Port Basics SDR2-USB Configuration Guide rev 1.0 32 The EIA RS-232C standard permits data rates up to 19200 bps and cable lengths up to 400 me
SDR2-USB Configuration Guide rev 1.0 Serial Port Basics 33 NOTE: Most serial devices format of eight data bits, no parity, and one stop bit (8N1).
Serial Port Basics SDR2-USB Configuration Guide rev 1.0 34 modem cable because it can connect two terminals (DTE’s) without the use of modems (DCE’s)
SDR2-USB Configuration Guide rev 1.0 Serial Port Basics 35 CTS, etc.), RS-232 devices use +3V to +25V to assert the signal and –3V to –25V to deass
Specifications SDR2-USB Configuration Guide rev 1.0 37 NOTE: The SDR2-USB datasheet contains further specifications. All specifications shown in thi
Specifications SDR2-USB Configuration Guide rev 1.0 38 B.1.6 J1 power receptacle pin configuration pin Function 1 +5.0 to +30 VDC 2 Ground Table B
Specifications SDR2-USB Configuration Guide rev 1.0 39 Notes:
SDR2-USB Configuration Guide rev 1.0 Getting Started Table of Contents 1. Getting Started ...
Getting Started SDR2-USB Configuration Guide rev 1.0 6. Service and Support ... 276.1 Exc
SDR2-USB Configuration Guide rev 1.0 Getting Started 5 NOTE: The data source is a device that transmits serial data for use by a computer, printer,
Getting Started SDR2-USB Configuration Guide rev 1.0 6 1.2 Before you start Before you start, be sure you have the following items available: • D
SDR2-USB Configuration Guide rev 1.0 Getting Started 7 NOTE: Your computer’s Windows installation may display different drive letters, file types, e
Comments to this Manuals